Designed for surface mounting as well as concealed installation for roof and facade
Are strong actuators suitable for roof openings - to be used together with ±24V control units or control units with MotorLink®
For windows with locking systems - designed for surface mounting as well as concealed installation
Designed for surface mounting as well as concealed installation
Actuator brackets and chain brackets for e.g chain actuators, spindel actuators.
Window actuators and their associated controls can form a critical element of modern building services. They make a significant contribution to the success – or failure – of a building’s internal environment and energy performance.
Equally, they are often a second thought, which can cause major headaches for designers, contractors and clients that have to pay to put them right, or live with the consequences for years to come.
You may have spent a good deal of time selecting an appropriate curtain wall or window system and designing it into the fenestration of the building, which now has the dynamic and crisp lines you desire.
Imagine turning up on site and finding out that the inside of your high performance windows have been covered with containment to conceal wiring to noisy and poorly-operated actuators that don’t seal the windows correctly, causing excessive cold draughts, heating load and complaints.
All window openers are the same, right? Wrong. But before you can select the right window openers for the job there are some fundamental points to consider.
We are specialists when it comes to choosing the right window openers for buildings. Our expertise is built on our knowledge of regulatory standards and experience from having completed thousands of projects across the whole of Europe.
Most facade window actuators are chain type. They are typically used for three main reasons.
Firstly, they deliver automated ventilation – increasingly chosen to add intelligence to the building’s ventilation, helping it breathe more effectively on its own.
Automated natural ventilation improves the indoor climate and comfort in the building through lower peak summer temperatures, enhances air quality and energy performance – and therefore productivity – while reducing running costs.
Secondly window actuators are also used to provide ventilation via out of reach openings using keypad control where manual winding gear is either considered too intrusive, expensive or high maintenance.
Thirdly, they may be used to provide smoke ventilation to improve building safety in the event of a fire.
Feel free to contact us here if you have any questions about window openers.
There are an increasing number of window actuators on the market of wildly varying quality and capability.
This has a direct effect on building performance, overall costs and client comfort and satisfaction – which is often overlooked.
Most standard window actuators have little or no intelligence. They consist of a glorified bike chain designed to bend only in the required planes, a motor and set of gears.
Without any intelligence, they are often operated in large poorly controlled ‘chunks’ of opening distance – associated with heavier oscillations around comfort set points, hunting, uncomfortable draughts, excessive energy consumption and potentially shorter actuator life.
In addition, many window actuators do not have pressure safety functionality. Typically window actuators have essential functions such as speed control to minimize noise.
Position feedback offers accurate positioning mm by mm to give the small openings commonly required for normal ventilation requirements as well as ensuring openings for night cooling remain within allowable security limits, and the potential to off-set costs by removing separate trickle vents fitted to windows.
Pressure safety functions can also make the difference between a pinch and severe injury.
Often the window profile can be used as a conduit for 24V actuator wiring. It may require some co-ordination during installation but the specification can offer the opportunity to do away with the ugly surface-mounted trunking that can spoil the overall look of the window system.
If vents are at high level, just preparing the mullions to allow cables to be pulled through allows cables to be hidden on top of the transom thus limiting their appearance on the face of the façade or windows. Alternatively, a matching cover profile might be an option. Again, this is often overlooked during the specification and tender process but a little thought in the specification, and preparation in the factory, can reduce cost and improve aesthetics later.
Depending on the combination of window profile and window actuator, the profile can also allow the window actuator to be hidden eg Velfac windows.
Some other aluminium systems also allow this solution but low profile systems often offer little room to hide the window actuators, which are therefore likely to be surface mounted. This is where you might also want to consider actuator colour and finishes in the specification.
On high load applications such as large roof lights with pitched opening, spindle actuators are usually used. The solid spindle housing hangs down into the space when closed, which many designers and clients find unsightly. New high capacity WMU 888 chain actuators from WindowMaster can address this issue and offer a powerful and neater solution.
Most window openers used for natural ventilation are 24V DC which give higher torque capacity and makes them electrically safer when using the window profile for containment. There are 240V actuators on the market, but these are generally designed for occasional use and are prone to overheating if used regularly, so are therefore normally avoided.
Window actuators come with different standard chain lengths: 265, 400, 500, 600 and 1.000mm.
Using the smallest window actuator possible will keep the unit size and cost down. The longer the chain, the bigger the links need to be to maintain integrity and therefore the bigger the housing to hide it when it is withdrawn.
To reduce the size and cost and improve aesthetics, use a 265mm chain where possible.
There are many schools of thought on calculating the opening or free area.
Generally, a typical profile will use around 40mm of chain to bridge the profile from the actuators fixings to the sash. Therefore, a 265mm chain will give around 225mm clear opening depending on the profile and mounting arrangement.
Do you have questions about the opening areas for your project? Feel free to contact us. We can help you choose the right window openers.
Research suggests that high level (typically two metres and above from floor level) top-hung outward opening windows are the most effective overall solution for natural ventilation.
Their opening areas can be supplemented by manual low level windows if required for operation on hotter days. These are often limited to 100mm openings due to the risk of falling, and the risk of obstruction if opening onto a thoroughfare.
Selecting high level openings minimises a number of risks. Draughts when controlling CO2 in winter are reduced because a small amount of cold air introduced at high level mixes with warm air and carries further into the room before falling to body height.
Security risks are reduced because insurance companies generally prefer small openings at higher level if night cooling. The risks from entrapment are lowered because while intelligent actuators have pressure safety functionality, they can still pinch, so it’s best to locate these at higher level.
Avoiding side-hung windows removes the risk of a scissor action at body height which can present a safety hazard. In addition, the lower element of the opening can introduce cold air at body height.
It is important to note that different window profiles have differing requirements for the number of operating handles. This applies to window actuators too. This is normally associated with the rigidity, or flex of the window profile around the pull point(s) and the frame’s capacity to maintain a seal around the perimeter of the vent.
It is less associated with window actuator power or opening/closing ability and is therefore dictated by the vent fabricator or profile supplier. The vent width limit for a single window actuator can vary from profile to profile from 700mm to 1.500mm (eg Velfac @ 1.500), though for aluminium profiles 1.200mm is normally used as a rule of thumb.
It is important to get confirmation of this if more window actuators are required because this not only impacts on actuator costs but also on associated power supplies and wiring. If in doubt, consulting WindowMaster or fabricators early on may prove worthwhile.
Most quality window actuators look similar but how the actuator looks, while aesthetically important, has no bearing on how successfully the window actuator will deliver on its requirements.
When creating the specification, any expectations you have for the benefit of the project and client should be made explicit. Decide which of the following points are important for the project and your client:
The actuator must provide two-way communication with the control panel to enable it to operate at a very slow speed when in the automatic mode, which can reduce noise and any potential impact or disturbance to the occupants.
It can also enable the motors to operate at a faster speed when activated by the manual keypads, for example, in order to provide an immediate visual response to the user, and at full speed in the event of an alarm signal for smoke clearance.
Your window opener must have the ability to monitor for entrapment on specified windows by communication via the microprocessors installed within the actuator and by monitoring in real-time the amount of electrical current being drawn and the precise position of the window to an accuracy of less than a millimetre.
The MotorLink® actuator will detect if an object becomes trapped in the leading edge of the window and prevent it from closing by monitoring the amount of current being drawn and then reversing the actuator to release the obstruction.
The sensitivity of the pressure safety must be adjustable, as the pressure safety function is a factor of the closing force of the actuator combined with the size and weight of the window, as well as the configuration of the window, its hinges and the rigidity of the profile itself. Therefore the overall performance and sensitivity of the system is dependent on all these factors combined and needs to be monitored and adjusted as the required forces can change during the life of the building.
The window or curtain walling fabricator should prepare the profiles for wiring routes with grommets and draw wires, using the frame as containment. If at high level a route should be provided through the mullions without having to bridge the inside face of the profile. If this cannot be avoided, consideration should be given to providing a matching cover profile.
We are happy to help you, if you have questions about selecting the right window openers for your building.
Where opening vents are about 1.200mm wide or more, the window or curtain walling supplier shall check whether two actuators are required.
This should be checked with the profile systems house as it is dictated by frame flex and the capacity to achieve a seal at the edges with a single pull point.
If required, the actuators must use MotorLink® to synchronise speed and time of operation.
The window actuator must provide two-way communication with the control panel to enable feedback to the control software on the window status and an early indication of any errors with the actuator operation or the wiring.
Write to us. We are happy to help.
By submitting this form, you consent to receive future communications such as newsletters from WindowMaster.
You are in the login area of certified WindowMaster partners. Access to the information platform for our certified partners is personal. You must log in with a user name and password to get access the contents of the extranet.
For further information contact your WindowMaster contact.